Main Article Content

Abstract

Jabiru J430 aircraft is a type of light aircraft produced by the Jabiru aircraft manufacturer with four passenger seats which has a length of 6550 mm and a height of 2200 mm with a high wing type with additional winglets. This study aims to determine the effect of installing a vortex generator on the upper surface of the Jabiru J430 aircraft wing on aerodynamic characteristics, especially at critical angle conditions. As it is known that the vortex generator functions to produce a vortex in the air flow on the upper surface of the wing so that it can delay the occurrence of flow separation and improve the performance of the wing. In this study, a comparison was made between the aerodynamic characteristics of the wing without a vortex generator and the addition of a vortex generator. The vortex generator used is a flat plate vortex with a counter-rotating configuration. From the simulation results, it can be seen that the airflow characteristics on the wings using a vortex generator are more stable when compared to airfoils without a vortex generator and it can be seen that the increase in the maximum lift coefficient from CL 0.997 (20 angle of attack) to CL 1.126 (angle of attack 24º) or an increase of 12.9%, and an increase in the drag coefficient occurs as the angle of attack increases.


 


 

Keywords

vortex generator Jabiru J430 CFD Coefficient Lift (CL) Coefficient Drag (CD)

Article Details

How to Cite
Analisis Aerodinamika pada Sayap JABIRU J430 dengan Penambahan Vortex Generator menggunakan Metode CFD. (2022). Jurnal Teknologi Kedirgantaraan, 7(1). https://doi.org/10.35894/jtk.v7i1.50

References

  1. Pangestu Wahyu., 2020, Analisis Performa Aerodinamik Pada Sayap Pesawat Jabiru J430 Dengan Menggunakan Variasi Bentuk Winglet, Skripsi, Program Studi Teknik Penerbangan, Universitas Dirgantara Marsekal Suryadarma, Jakarta.
  2. A. Romadhon, D. Herdiana.,2017, Analisis CFD Karakteristik Aerodinamika Pada Sayap Pesawat Lsu-05 Dengan Penambahan Vortex Generator, Jurnal Teknologi Dirgantara, No. 1, Vol .15, 45.
  3. Wings, M., 2019, how to build a wing in solidworks starting from coordinates, diakses tanggal 13 februari 2021.
  4. Haryadi, Setyo., 2015, Studi Numerik Penggunaan Vortex Generator Terhadap Boundary Layer Airfoil NACA 43018, Skripsi, Program Studi Teknik Pesawat Udara, Akademi Teknik dan Keselamatan Penerbangan Surabaya, Surabaya.
  5. Azmi Ulul, Sasongko Herman, 2015, Studi Eksperimen dan Numerik Pengaruh Penambahan Vortex Generator pada Airfoil NASA LS-0417, Jurnal Teknik ITS, Vol. 4, No. 1
  6. P. Martınez-Filgueira, U. Fernandez- Gamiz, E. Zulueta, I. Errasti, B. Fernandez-Gauna., 2017, Parametric study of low-profile vortex generators, International Journal Of Hydrogen Energy, Vol 1-13
  7. Dewangga Muhamad, Yamin Mohammad., 2020, Rancang Ulang Desain Impeller Kipas Sentrifugal Sistem Pendingin Mesin Sepeda Motor Skutik Dengan Metode Reverse Enginering, Jurnal Teknologi Universitas Muhammadiya Jakarta.
  8. Pilot's Handbook of Aeronautical Knowledge. FAA. p. Chapter 5,
  9. Aerodynamics of flight.